Cirronet SEM2410 Betriebsanweisung Seite 22
- Seite / 37
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SEM2410
Access Control Users
This dialog allows the modification of logins and the ability to add new users.
Note: Click on Save Settings to store the system configuration changes in non-volatile FLASH
memory. The user may either click on “Reset” to reboot the processor, click on “Logout” to end the
browser session or simply close the browser window.
Console Port
The SEM can be configured two ways: Through a browser session once an IP address has been
obtained and through a serial session through the console port. The settings for the console port
are 38400 baud, 8 data bits, 1 stop bit, and no parity. The WinSEM program can be used to set
up the SEM through the Console port. The appropriate serial port must be selected in WinSEM,
but the program will automatically set up the serial port. After a few seconds the SEM firmware
version is displayed followed by the
SEM> prompt.
To set the IP number of the SEM, use the ip command.
ip <xxx.xxx.xxx.xxx> {yyy.yyy.yyy.yyy}
Where x is the new IP address and y is the optional netmask number.
Once a valid IP address has been entered in the SEM, a second method to configure the SEM is
through a telnet session. Most telnet programs work with the SEM. Windows
95/98/NT/2000/ME have a telnet program that works with the SEM. A telnet session can be
started by clicking on Start->Run if you have Windows 95/98/NT/2000 and the TCP/IP client
has been installed. For a SEM with an IP address of 192.168.0.254, enter the following
information in the dialog box:
telnet 192.168.0.254
A telnet window will open up prompting for a Username/Password. The default Username is
“admin”, the default Password is “Cirronet”. The first line is the version of the SEM firmware
followed by the prompt:
SEM>
If the SEM is to transmit data to devices not on its subnet, a default router must be specified. To
enter the default routing address, use the route command.
route add default <xxx.xxx.xxx.xxx> {yyy.yyy.yyy.yyy}
Where x is the IP address of the gateway device and y is the optional netmask number.
To configure a SEM as a master device, use the bridge command:
bridge master<CR>
Store the changed configuration parameters in non-volatile memory with the save command:
save<CR>
© 2000- 2005 Cirronet™ Inc 17 M-2410-0018 Rev C
- SEM2410 /X /D /DX 1
- User’s Guide 1
- Declaration of Conformity 3
- WARNING!! 4
- Table of Contents 5
- Introduction 6
- Getting Started 7
- SEM2410, SEM2410D 8
- SEM2410X/DX 10
- SEM2410 11
- Configuring the SEM 16
- HTML Setup 19
- SEM Operation 24
- SEM Command Set 27
- Specifications 35
- Troubleshooting 36
- Warranty 37
Verwandte Produkte und Handbücher für Vernetzung Cirronet SEM2410
Vernetzung Cirronet CR-SEHX Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Vernetzung Cirronet HN214D Betriebsanweisung
(64 Seiten)
(64 Seiten)
Sony D-NE720 manuály
Uživatelské manuály a uživatelské příručky pro ne Sony D-NE720.
Poskytujeme 3 manuály pdf Sony D-NE720 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Kommentare zu diesen Handbüchern